Smart Home Guide
Wi-Fi in the 6 GHz band: what the FCC allows indoor routers, standard-power gear and portable gadgets
Our take
Since 2020 the FCC has widened unlicensed use of the 6 GHz band in four device classes, the newest from April 2026. Where each may work, at what power, and why.
By Review Boon Team · · 4 min read
Key points
- The FCC expanded unlicensed use of the 1,200 megahertz at 5.925-7.125 GHz in 2020, and says the rules brought a wave of Wi-Fi 6 and 6E devices.
- Low-power indoor access points may use the whole band; standard-power ones are limited to two sub-bands and need an automated frequency coordination system.
- Very low power devices may work indoors and outdoors without that system at up to 14 dBm, across the whole band since May 5, 2025.
- Geofenced variable power devices, allowed from April 27, 2026, may reach 24 dBm in two sub-bands if they avoid exclusion zones around microwave links and observatories.
- The FCC requires geofencing systems to use registration data only to protect incumbents and resolve interference, and devices need not report exact coordinates.
In April 2020, the Federal Communications Commission expanded unlicensed use of the 1,200 megahertz between 5.925 and 7.125 GHz, known as the 6 GHz band, for unlicensed devices such as Wi-Fi equipment. The agency later wrote that the rules “unleashed a torrent of new devices taking advantage of the newer Wi-Fi 6 and 6E standards.”
The band was not empty. Licensed point-to-point microwave links are its largest users, carrying traffic for utilities, phone networks, railroads, pipelines and public safety agencies. Satellite operators, TV crews sending pictures back to the studio, licensed wireless microphones and radio astronomers use parts of it too. So the FCC has let unlicensed devices in by class, each with its own limits. There are now four.
The four classes
| Class (year created) | Where it may operate | Which frequencies | Power and control |
|---|---|---|---|
| Low-power indoor access points (2020) | Indoors | Whole band | Lower power than standard power; must use a contention-based protocol |
| Standard-power access points and fixed clients (2020) | Not limited to indoors | U-NII-5 and U-NII-7 | Under the control of an automated frequency coordination (AFC) system |
| Very low power, VLP (2023; whole band from May 5, 2025) | Anywhere, indoors and outdoors, but not on fixed outdoor infrastructure | Whole band | Up to 14 dBm EIRP and -5 dBm/MHz; no AFC system |
| Geofenced variable power, GVP (2026; effective April 27, 2026) | Mobile use; not on fixed outdoor infrastructure or aboard aircraft | U-NII-5 and U-NII-7 | Access points up to 24 dBm EIRP and 11 dBm/MHz, outside exclusion zones; clients 6 dB lower |
Client devices, such as laptops, work under the control of an access point, at power levels that depend on the type of access point, the FCC says. Clients of standard-power and GVP access points must stay 6 dB below their access point's maximum, and the FCC has acknowledged that one motivation for the same gap with low-power indoor gear was to keep the clients indoors.
Very low power: portable gear, no database
The FCC created the VLP class in an order released on November 1, 2023, first in the U-NII-5 and U-NII-7 sub-bands, and extended it to the whole band in an order adopted on December 11, 2024 and effective May 5, 2025. VLP devices do not need permission from a coordination system; instead they are held to low power, must be able to cut it further, and must use a contention-based protocol. They must also try frequencies above 6105 MHz before lower ones, to protect services below the band.
The FCC expects the class to support augmented and virtual reality and body-worn technologies, it said, providing high data rates over short distances. VLP devices may not be used on low-flying aircraft, drones or oil platforms, though on aircraft above 10,000 feet they may use 5.925-6.425 GHz.
Geofenced variable power: more power, with a map
The newest class, adopted on January 29, 2026, lets a portable device transmit at higher power than VLP if it knows where it is. Each GVP access point must have a geolocation capability and get exclusion zones from a geofencing system, then stay off frequencies used by nearby microwave links, and off part of the U-NII-7 sub-band near radio astronomy observatories. Access points must check in with the geofencing system daily for updated zones. The FCC left the two other sub-bands, U-NII-6 and U-NII-8, for later.
The FCC said it was adopting the higher power levels requested by industry, combined with geofencing. Commenters filing as Apple, Broadcom et al. said the higher power density would help applications that rely on narrow channels, such as high bitrate audio, and the higher maximum power would help data-heavy uses such as AR/VR, car technology, screen mirroring and hotspots. They had argued that geofencing would require expensive new hardware and software, which the lower limits first proposed would not justify.
Not everyone agreed. AT&T argued against letting each device calculate its own exclusion zones, and utility groups favored a central system to protect microwave links. The FCC did not adopt the distributed approach and requires a centralized geofencing system, while letting administrators choose how to run it. It also declined a request from Cisco and HP Enterprise to limit GVP power to protect enterprise Wi-Fi, saying unlicensed devices are expected to share the band.
What happens to location data
Because GVP depends on knowing a device's location, the order addresses privacy. A GVP access point is to give the geofencing system only the information it needs to receive its area of operation, and it can download zones for an area as large as a whole state, so it does not have to report its exact latitude and longitude or keep sending coordinates as it moves. Geofencing systems must keep registered information in a secure database until an access point has not checked in for more than three months, and may use it only to protect incumbents and for potential interference mitigation, the FCC said.
The orders set rules for device makers and the systems they rely on. They do not say how a product's box or spec sheet must describe its class. For other buying questions about home networks, our guide to Matter covers how smart home devices work together.
This guide is based on the FCC's 2025 and 2026 orders on the 6 GHz band as published in the Federal Register, read on November 20, 2026. It does not assess any router or device.
Sources
- Unlicensed Use of the 6 GHz Band; Expanding Flexible Use in Mid-Band Spectrum Between 3.7 and 24 GHz, final rule (Third Report and Order, FCC 24-125) Federal Communications Commission, Federal Register (govinfo), March 6, 2025
- Unlicensed Use of the 6 GHz Band; Expanding Flexible Use in Mid-Band Spectrum Between 3.7 and 24 GHz, final rule (Fourth Report and Order, FCC 26-1) Federal Communications Commission, Federal Register (govinfo), February 25, 2026
Researched and drafted with AI assistance, then checked against the 2 sources above in a separate fact-check on November 20, 2026. Spotted an error? Tell us.